Heap corruption

QNX SDP8.0Programmer's GuideDeveloper

Heap corruption occurs when a program damages the allocator's view of the heap.

The outcome can be relatively benign and cause a memory leak (where some memory isn't returned to the heap and is inaccessible to the program afterward), or it may be fatal and cause a memory fault, usually within the allocator itself. A memory fault typically occurs within the allocator when it manipulates one or more of its free lists after the heap has been corrupted.

It's especially difficult to identify the source of corruption when the source of the fault is located in another part of the code base. This is likely to happen if the fault occurs when:

  • a program attempts to free memory
  • a program attempts to allocate memory after it's been freed
  • the heap is corrupted long before the release of a block of memory
  • the fault occurs on a subsequent block of memory
  • adjacent memory blocks are used
  • your program is multithreaded
  • the memory allocation strategy changes

Adjacent memory blocks

When adjacent blocks are used, a program that writes outside of the bounds can corrupt the allocator's information about the block of memory it's using, as well as the allocator's view of the heap. The view may include a block of memory that's before or after the block being used, and it may or may not be allocated. In this case, a fault in the allocator will likely occur during an unrelated attempt to allocate or release memory.

Multithreaded programs

Multithreaded execution may cause a fault to occur in a different thread from the thread that actually corrupted the heap, because threads interleave requests to allocate or release memory.

When the source of corruption is located in another part of the code base, conventional debugging techniques usually prove to be ineffective. Conventional debugging typically applies breakpoints—such as stopping the program from executing—to narrow down the offending section of code. While this may be effective for single-threaded programs, it's often unyielding for multithreaded execution because the fault may occur at an unpredictable time, and the act of debugging the program may influence the appearance of the fault by altering the way that thread execution occurs.

Even when the source of the error has been narrowed down, there may be a substantial amount of manipulation performed on the block before it's released, particularly for long-lived heap buffers.

Allocation strategy

A program that works in a particular memory allocation strategy may abort when the strategy is changed in a minor way. A good example of this is a memory overrun condition (see Common sources, below) where the allocator is allowed to return blocks that are larger than requested so it can satisfy allocation requests.

Under this circumstance, the program may behave normally in the presence of overrun conditions. However, a simple change, such as changing the size of the block requested, may result in the allocation of a block of the exact size requested, resulting in a fatal error for the offending program.

Fatal errors may also occur if the allocator is configured slightly differently, or if the allocator policy is changed in a subsequent release of the runtime library. This makes it all the more important to detect errors early in the lifecycle of an application, even if it doesn't exhibit fatal errors in the testing phase.

Common sources

Some of the most common sources of heap corruption include:

  • a memory assignment that corrupts the header of an allocated block
  • an incorrect argument that's passed to a memory allocation function
  • an allocator that made certain assumptions in order to avoid keeping additional memory to validate information, or to avoid costly runtime checking
  • invalid information that's passed in a request, such as to free()
  • overrun and underrun errors
  • releasing memory
  • using uninitialized or stale pointers

Even the most robust allocator can occasionally fall prey to the above problems. Let's take a look at the last three items in more detail.

Overrun and underrun errors
Overrun and underrun errors occur when your program writes outside of the bounds of the allocated block. They're one of the most difficult type of heap corruption to track down, and usually the most fatal to program execution.

Overrun errors occur when the program writes past the end of the allocated block. Frequently this causes corruption in an adjacent block in the heap, whether or not it's allocated. When this occurs, the behavior that's observed varies depending on whether that block is allocated or free, and whether it's associated with a part of the program related to the source of the error. When a neighboring block that's allocated becomes corrupted, the corruption is usually apparent when that block is released elsewhere in the program. When an unallocated block becomes corrupted, a fatal error will usually result during a subsequent allocation request. Although this may well be the next allocation request, it actually depends on a complex set of conditions that could result in a fault at a much later point in time, in a completely unrelated section of the program, especially when small blocks of memory are involved.

Underrun errors occur when the program writes before the start of the allocated block. Often they corrupt the header of the block itself, and sometimes, the preceding block in memory. Underrun errors usually result in a fault that occurs when the program attempts to release a corrupted block.

Releasing memory
In order to release memory, your program must track the pointer for the allocated block and pass it to the free() function. If the pointer is stale, or if it doesn't point to the exact start of the allocated block, it may result in heap corruption.

A pointer is stale when it refers to a block of memory that's already been released. A duplicate request to free() involves passing free() a stale pointer—there's no way to know whether this pointer refers to unallocated memory, or to memory that's been used to satisfy an allocation request in another part of the program.

Passing a stale pointer to free() may result in a fault in the allocator, or worse, it may release a block that's been used to satisfy another allocation request. If this happens, the code making the allocation request may compete with another section of code that subsequently allocated the same region of heap, resulting in corrupted data for one or both.

The most effective way to avoid this error is to NULL out pointers when the block is released, but this is uncommon, and difficult to do when pointers are aliased in any way.

A second common source of errors is to attempt to release an interior pointer (i.e., one that's somewhere inside the allocated block rather than at the beginning). This isn't a legal operation, but it may occur when the pointer has been used in conjunction with pointer arithmetic. The result of providing an interior pointer is highly dependent on the allocator and is largely unpredictable, but it frequently results in a fault in the free() call.

A rarer source of errors is to pass an uninitialized pointer to free(). If the uninitialized pointer is an automatic (stack) variable, it may point to a heap buffer, causing the types of coherency problems described for duplicate free() requests above. If the pointer contains some other non-NULL value, it may cause a fault in the allocator.

Using uninitialized or stale pointers
If you use uninitialized or stale pointers, you might corrupt the data in a heap buffer that's allocated to another part of the program, or see memory overrun or underrun errors.
Page updated: