Home
QNX SDP 8.0 BSP Documentation
The board support package (BSP) documentation includes user guides that describe how to work with the BSPs provided for the QNX Software Development Platform (SDP) 8.0, and release notes that describe the supported features and hardware as well as any known issues for each BSP.
Intel
Generic x86_64
User's Guide

QNX SDP 8.0 BSP Documentation
The board support package (BSP) documentation includes user guides that describe how to work with the BSPs provided for the QNX Software Development Platform (SDP) 8.0, and release notes that describe the supported features and hardware as well as any known issues for each BSP.
- AMD
- Broadcom
- Intel
  - Generic x86_64
    - Release Notes
    - User's Guide
      - Before You Begin
        Before you begin working with this BSP, you should become familiar with the resources available to you to work with QNX embedded systems.
      - About This BSP
        This chapter lists what's included in the BSP, the supported host system operating systems, and other relevant information to use this BSP.
      - Installation Notes
        These installation notes describe how to install and boot a board using this BSP.
      - Build the BSP
        You can use the QNX Momentics IDE or the commandline on Linux or Windows to build an image.
      - Generic x86_64_Driver Commands
        The tables below provide a summary of driver commands.
      - Working with Intel Elkhart Lake CRB platform
        The Intel Elkhart Lake CRB platform uses many of the same source and binaries provided for the generic BSP, however, there are a few differences. The boards we provide buildfiles for are Intel Elkhart Lake CRB boards.
      - Working with Nexcobot Elkhart Lake SCB100 platform
        This chapter describes the steps to build the QNX SBL container sbl_os and boot it on the Nexcobot Elkhart Lake SCB100 board.
      - Working with SECO Amston Lake platform
        The SECO Amston Lake platform uses many of the same sources and binaries provided for the generic BSP, with a few differences. This BSP was developed and validated on the SECO Amston Lake SOM-SMARC-ASL (CSE08REVB - L1 config) with Carrier-SM-B79 (CSB79REVB), using UEFI firmware - version 1.00.00.
- NXP
- Texas Instruments
Typographical Conventions, Support, and Licensing
This section describes the typographical conventions used throughout the documentation, explains how to obtain technical support, and provides some information about licensing.

About This Guide

This guide contains installation and start-up instructions for the QNX Board Support Package (BSP) for x86_64 platforms; x86 (32-bit) isn't supported in this release.

At times, there's specific information for variants of the x86_64 platforms based on a particular processor family or SoC. You should refer to information in those chapters if your board uses that processor family or SoC.

This documentation includes:

an overview of QNX BSP
links to documentation about how to build QNX embedded systems, which you should read before you begin working with this BSP
what's new in the BSPs for this release
the structure and contents of the BSP
how to prepare a bootable USB device (e.g., USB memory stick)
how to install the BSP and boot it on a board
how to build your BSP


To find out about:	See:
The resources available to you, and what you should know before starting to work with this BSP	Before You Begin
What's included in the BSP, supported host operating systems, and boards	About This BSP
Installing this BSP	Installation Notes
Building this BSP	Build the BSP
Driver commands	Generic x86_64_Driver Commands
Working with Intel Elkhart Lake CRB platform	Working with Intel Elkhart Lake CRB platform
Working with Nexcobot Elkhart Lake SCB100 platform	Working with Nexcobot Elkhart Lake SCB100 platform
Working with SECO Amston Lake SOM-SMARC-ASL platform	Working with SECO Amston Lake platform

Page updated: September 26, 2025