Generic flash filesystem
Note:
You must be root to start this driver.
Syntax:
devf-generic
[-Aa] [-b priority] [-D] [-d log_method] [-E] [-e arg]
[-f verifylevel] [-i arrayindex[,partindex]]
[-L limit] [-l] [-m mountover] [-O] [-P lock_mode]
[-p backgroundpercent[,superlimit]] [-R] [-r]
[-S sector_erase_latency]
[-s base[,wsize[,aoffset[,asize[,usize[,bwidth[,ileave]]]]]]]
[-T max_erase_diff] [-t hi_water[,lo_water[,max]]] [-u update]
[-V] [-v] [-W num] [-w buffersize] [-x type]
Targets:
Most flash devices, including Intel StrataFlash, most of the Spansion MirrorBit parts, and
some of the Numonyx M29W series.
Options:
- -A
- When registering the path names for the partitions with
resmgr_attach(),
use the _RESMGR_FLAG_AFTER flag to force the path to be
resolved after others with the same pathname at the same mountpoint.
- -a
- Don't automount filesystem partitions present on the media.
If you specify both the -a and -R options,
the driver ignores the -R option.
- -b priority
- Enable background reclaim at the specified priority.
By default, background reclamation is disabled.
- -D
- Enable automatic detection of error-correcting code (ECC) mode.
If you specify this option, you don't need to specify -x.
Note:
Don't mix ECC-enabled partitions and ECC-disabled partitions;
the driver doesn't support this.
- -d log_method
- Control the logging from the flash driver.
The possible values for log_method are:
- 0 — log to stdout (the default)
- 1 — log to
slogger
- 2 — log to both stdout and slogger
- -E
- Don't daemonize.
If the driver detects a corrupt filesystem, the exit status is that
filesystem's partition number plus 1.
- -e arg
- Only enumerate the flash partitions, instead of doing a full scan
and mount:
- If arg is an integer, the flash driver automounts all partitions with a partition number
less than or equal to arg.
For example, assume we have a flash layout as follows:
- /dev/fs0p0 — raw
- /dev/fs0p1 — formatted
- /dev/fs0p2 — formatted
- /dev/fs0p3 — formatted
If you start the driver with -e 1, the driver creates all the
raw entries in /dev, but mounts only
/dev/fs0p1 (/dev/fs0p0 is raw, so it's never
mounted, regardless of the -e option).
- If arg is a string, the driver interprets it as a colon-separated list of
exact paths to mount, if found.
- -f verifylevel
- Enable flash verification (default=0, 0=none, write=1, erase=2, all=3).
- -i arrayindex[,partindex]
- Starting socket index and first partition index;
0 ≥ index ≥15. The default is 0,0.
Use this to give multiple drivers unique IDs.
The -i option is just a suggestion for the resource
database manager; the selected indexes can be larger.
- -L limit
- The number of retries to make if the physical flash erase function for a unit fails.
The default is 0.
- -l
- List the available flash databases and then exit.
- -m mountover
- Override the mountpoints assigned to the file system that are formatted
with an empty (i.e., flashctl -p/dev/fs0p0 -f -n "") mountpoint. The mountover
argument can include two
%X format specifiers (like those for printf())
that are replaced by the socket index and the partition index.
Note:
The
-m option doesn't override a mountpoint specified with
mkefs.
- -O
- Use a directory lock for I/O operations.
- -P lock_mode
- Set the protection mode for Spansion-compatible devices:
- 0 — no lock (the default)
- 1 — persistent lock mode
- 2 — dynamic lock mode
- -p backgroundpercent[,superlimit]
- Set the background-reclaim percentage trigger (stale space over free
space) and, optionally, the superseded extent limit before reclaim.
The default is 100,16.
- -R
- Mount any automount filesystems as read-only.
This option doesn't affect raw partition mounts, and it has an effect
only at startup and initialization.
Any subsequent mounting (with either
flashctl
or
mount)
ignores the -R option.
If you also specify the -a option, the driver ignores the
-R option.
- -r
- Enable fault recovery for dirty extents, dangling extents, and partial
reclaims.
Note:
You should always specify the -r option unless you're
trying to debug an issue concerning flash corruption.
If you don't specify -r, and a power failure occurs,
the following can happen:
- You can waste space.
If an erasure was happening when the power was cut off,
there will be some "dangling" extents (i.e., marked for
deletion, but not actually deleted).
If you specify the -vv option, the driver prints
dangle for every dangling extent found.
These extents will continue to occupy space forever, until they're
deleted.
Using the -r option will cause them to be reclaimed.
- The system may be marked as read-only.
If the driver detects an error in the structure of the filesystem,
and you haven't specified the
-r option, the driver marks the partition as read-only,
so that it can't be further damaged.
- If a reclaim operation is interrupted by a power loss, the spare block
may be unusable.
In this case, if you specify the -vv option, the driver prints
partial to the console.
The partition is still read-write, but reclaims are turned off;
if you continue to overwrite files, you'll eventually fill the
filesystem with stale data.
- -S sector_erase_latency
- Set the simulated sector erase latency in milliseconds (max = 10000).
- -s base[,wsize[,aoffset[,asize[,usize[,bwidth[,ileave]]]]]]
- Set socket options, normally the base physical address, window size,
array offset, array size, unit size, bus width, and interleave. The format is left flexible
for socket services with customized drivers. This option must be specified.
The arguments are:
- base
- Physical base address of the flash part. This value is board-specific.
- wsize
- Size of the physically contiguous flash part.
- aoffset
- For SRAM, the offset from the base address to the start of the flash array.
- asize
- For SRAM, the size of the flash array. The default is equal to
wsize.
- usize
- The size of a physical erase sector. For SRAM, this number can be any
power of two. 64 KB should be the minimum, for performance reasons.
- bwidth
- The total width of the data bus, as seen from the microprocessor's
perspective. This is the width of one flash chip multiplied by the
interleave.
The value must be a power of 2 (1, 2, 4, or 8).
- ileave
- The number of flash chips arranged on the data bus.
Two 16-bit wide chips used as the upper and lower halves of a 32-bit
databus give an interleave of 2.
This number must be a power of 2 (1, 2, 4, or 8).
You can specify the base physical address, sizes, and offset
in octal (1000), hexadecimal (0x200), or
decimal (512).
The sizes must be a power of two, and you can specify them with any of
the following suffixes:
- (nothing) — bytes
- k — kilobytes
- m — megabytes
- -T max_erase_diff
- Set the threshold value (maximum erase count − minimum erase count
in a partition) to trigger wear-levelling.
The default value is two times the sector number in the partition.
Typically, for very large partitions containing more than 1000 sectors,
you should use this option to specify a threshold (for example, 1000)
to make the sector erasure counts more evenly distributed across the
entire partition.
- -t hi_water[,lo_water[,max]]
- Set the high water, low water, and maximum attributes of the thread pool;
the increment (i.e., the number of threads created at one time) is 1.
The default is 4,2,100.
The values must be related as follows:
- 0 < hi_water < max
- 0 ≤ lo_water ≤ hi_water
- hi_water < max ≤ 100
- -u update
- Specify the update level for timestamps.
POSIX specifies that timestamps be kept when you access, create, or
modify a file.
FFSv3 is documented as not supporting the access
timestamp, in order to reduce wear on the hardware.
The values for update are:
- 0 — don't update the modification time for files (the default).
- 1 — update the modification time for files according to the POSIX rules.
- 2 — update the modification time for files, as well as for
the parent directory.
Note:
The -u2 option is very, very expensive and will cause many
reclaims because the time updates have to flow right up to the root
directory, so one file update may cause many directory updates.
- -V
- Display filesystem and MTD version information, and then exit.
- -v
- Be verbose; specify additional v characters for more verbosity.
For more information, see
"Verbose output,"
below.
- -W num
- Use the workaround identifed by num.
The workarounds available (if any) depend on the board.
- -w buffersize
- Write (append) buffer size in bytes.
The default buffersize is 512.
Using a larger write buffer prevents the creation of very small extents, reducing overhead.
If buffersize is 0, appending is disabled.
- -x type
- Enable software ECC mode.
Specify type as 1 for 64-byte alignment ECC, or 2 for 32-byte.
Note:
Don't mix ECC-enabled partitions and ECC-disabled partitions;
the driver doesn't support this.
Description:
The devf-generic manager provides Flash filesystem
support for any standard flash device. Typically, all you need to do is to pass
the address and size using the -s option. The manager should detect the
device automatically.
For information on creating a custom variant of devf-generic
for your embedded system, see the
Customizing the Flash Filesystem
chapter of Building Embedded Systems
The default filenames are as follows (you can use the -i option to
change the ID, n, appended to /dev/fs):
- /dev/fsn
- Default mountpoint for socket n.
- /dev/fsnp0
- Raw access for socket n, partition 0.
- mountpoint
- Flash filesystem mountpoint for socket n, partition 0 with
transparent decompression.
You can specify the mountpoint above with the
mount attribute of the
mkefs
command, and override it with the
-n option to
flashctl.
By default, it's /fsnp0.
Note:
- If you erase a raw partition or the raw array (socket),
you might erase any boot monitor,
BIOS, or other data installed by the manufacturer.
Check the documentation for the board.
- You can't erase multiple partitions simultaneously.
The driver probes the hardware to determine its block size.
If you need to know the block size, you can:
- Look in the documentation for the hardware.
Or:
- Start the driver in verbose mode by specifying the -v option.
In the output, U: indicates the number of units (also known as
blocks or sectors),
and S: indicates the block size.
Both numbers are in hexadecimal.
Or:
- Start the driver, and then run
flashctl,
specifying the -i option.
The block size is the effective physical block size of the NOR chip
(i.e., the chip sector size multiplied by the interleave).
This is used for erasing; the filesystem itself uses variable-sized extents to store data.
The devf-* drivers support 32- and 64-byte error-correcting code (ECC) partitions.
If you use 32-byte ECC:
- The interleave of the flash chips must be 1, or the driver reports an error.
- You must use the -b 5 option for flashctl to specify the alignment.
- You must use the ecc_on=2 attribute in the buildfile for
mkefs.
If you use 64-byte ECC:
- The interleave of the flash chips can be 1 or 2.
- You must use the -b 6 option for flashctl to specify the alignment.
- You must use the ecc_on=1 attribute in the buildfile for
mkefs.
The mkefs utility automatically handles the formatting alignment.
Verbose output
If you specify the -v option, a devf-* driver provides
some useful information.
This section describes the output that you get if you specify -vvv;
at higher levels of verbosity, the output also includes messages about the
use of malloc() and free(), but these aren't likely
to be useful to you.
The output starts with something like this:
Flash Development Library - HEAD
Build: Jan 15 2010 13:00:00
MTD Build: Jan 15 2010, 13:25:55
These lines identify the source branch of the build, as well as the
build times for libfs-flash3.a and
libmtd-flash.a.
The rest of the messages that the driver prints are variable; messages are
printed as the driver discovers things of interest.
The general format of a message is
(devf tN::function:line) Message string
where tN is the thread printing the message,
function is the function emitting the message, and
line is the line number that emitted the message.
The standard messages include the following:
- (devf t1::f3s_skt_attach:109) fs0 socket RAM (flash simulation)
- The flash driver located a flash socket, number zero (fs0).
This message also indicates that the hardware identification succeeded.
- (devf t1::f3s_flash_probe:248) chip total = 1, bus_width = 8, interleave = 2
- After identifying the hardware, the driver prints the geometry.
The chip total is the number of contiguous chips.
The bus width is the size of the data bus, in bytes.
The interleave is the number of physical chips sharing
the data bus (high and low halves of the data bus, for example).
This particular example indicates that there are two physical chips
sharing a 64-bit data bus.
- (devf t1::f3s_skt_attach:135) fs0 array SRAM U: 80 S: 020000
- The flash driver has allocated the flash array
(i.e., the storage media) of type SRAM, with 0x80 hardware sectors,
and a sector size of 0x020000 bytes.
- (devf t1::f3s_recover_boot:248) fs0p0 boot P[00] U: 80
- The filesystem is now scanning for partitions.
It has found a boot header, and has named the partition
/dev/fs0p0. The boot signature is located on physical
block 0, and the partition has 0x80 sectors (called "units" in
devf-* nomenclature).
- (devf t1::f3s_recover_reclaim:989) fs0p0 spare P[7F]
- The second phase of the startup scan is processing
/dev/fs0p0, and has found a spare block.
The spare block is located on physical sector 0x7F.
- (devf t3::f3s_table_find:66) fs0p1 raw U: 09
- A region of flash was found that isn't formatted.
The region is given the name /dev/fs0p1; its size is 0x09
sectors.
Examples:
Start devf-generic and automatically mount the flash filesystem
partitions at the base address 0xFF000 with a window size of 16 megabytes,
with an initial fault recovery process, most POSIX semantics
enabled and background reclaim at priority 5:
devf-generic -s 0xFF000,16M -r -u2 -b5 &
Create a 32 MB flash partition, with a 64 KB unit (sector) size:
devf-generic -s0,32m,,,64k -v -r
Create a 128 MB flash partition, with large block sizes (to speed formatting):
devf-generic -s0,128m,,,512k -v -r
Create a 4 MB partition:
devf-generic -s0,4m,,,64k -v -r
Create a 16 MB flash partition, from a given physical address, with a 128 KB
unit size, and a 16-bit wide data bus:
devf-generic -s0xa4000000,16m,,,128k,2 -v -r
Create a 16 MB flash partition, from a given physical address, with a 256 KB
unit size, and a 32-bit-wide data bus, with an interleave of two:
devf-generic -s0,16m,,,256k,4,2 -v -r
Caveats:
You must specify the -s option when using this driver.
Although the Flash filesystem supports most POSIX semantics, some
functionality isn't implemented in order to keep the driver simple and
efficient. The unsupported POSIX semantics include:
- Hard links, and everything related to hard links (the
. and .. directories don't exist,
struct stat's nlink member is hard-coded, and
unlink()
of directories returns ENOTSUP).
- Access times aren't updated on the media; they're set to the modification time.
QNX Neutrino flash filesystem version 3 no longer
provides built-in decompression.
The flash filesystem's decompression functionality has moved into the
inflator
resource manager. You should now use the deflate utility
to compress files.
Performance might be slow when multiple writers are writing randomly
to a shared file or to a shared directory (e.g., using unlink or
rename).
In these cases,
the offset pointers have to be rewound for every access.
There's no performance penalty when appending to a file, or when
creating files with open(O_CREAT),
mkdir, mknod, or link.