dhcrelay

Dynamic Host Configuration Protocol relay agent

Syntax:

dhcrelay [-4] [-dqaD] [-p port] [-c count]
         [-A length] [-m append | replace | forward | discard]
         [ -i interface0 [... -i interfaceN]]
         server0 [ ...serverN ]

dhcrelay -6 [-dqI] [-p port] [-c count]
         -l lower0 [... -l lowerN]
         -u upper0 [... -u upperN]

Runs on:

QNX Neutrino

Options:

Protocol-selection options:

-4
Run dhcrelay as a DHCPv4/BOOTP relay agent. This is the default mode of operation, so the option is not necessary, but may be specified for clarity. Incompatible with -6.
-6
Run dhcrelay as a DHCPv6 relay agent. Incompatible with the -4 option. If you specify this option, the names of the default files include a "6":
IPv4 name IPv6 name
/var/run/dhcrelay.pid /var/run/dhcrelay6.pid

Specifying DHCPv4/BOOTP servers:

In DHCPv4 mode, a list of one or more server addresses must be specified on the command line, to which DHCP/BOOTP queries should be relayed.

Options available for both DHCPv4 and DHCPv6:

-c count
The maximum hop count. When forwarding packets, dhcrelay discards packets that have reached a hop count of count. The default is 10, and the maximum is 255.
-d
Force dhcrelay to run as a foreground process. Useful when running dhcrelay under a debugger, or running out of inittab on System V systems.
-p port
Listen and transmit on the specified port. This is mostly useful for debugging purposes. The default is port 67 for DHCPv4/BOOTP, or port 547 for DHCPv6.
-q
Quiet mode; prevents dhcrelay from printing its network configuration on startup.

Options available in DHCPv4 mode only:

-a
Append an agent option field to each request before forwarding it to the server. Agent option fields in responses sent from servers to clients will be stripped before forwarding such responses back to the client. The agent option field will contain two agent options: the Circuit ID suboption and the Remote ID suboption. Currently, the Circuit ID will be the printable name of the interface on which the client request was received. The client supports inclusion of a Remote ID suboption as well, but this is not used by default.
-A length
Specify the maximum packet size to send to a DHCPv4/BOOTP server. This might be done to allow sufficient space for the addition of relay agent options while still fitting into the Ethernet MTU size.
-D
Drop packets from upstream servers if they contain Relay Agent Information options that indicate they were generated in response to a query that came via a different relay agent. If this option is not specified, such packets will be relayed anyway.
-i ifname
Listen for DHCPv4/BOOTP queries on interface ifname. Multiple interfaces may be specified by using more than one -i option. If no interfaces are specified on the command line, dhcrelay will identify all network interfaces, eliminating non-broadcast interfaces if possible, and attempt to listen on all of them.
-m append | replace | forward | discard
Control the handling of incoming DHCPv4 packets which already contain relay agent options. If such a packet does not have giaddr set in its header, the DHCP standard requires that the packet be discarded. However, if giaddr is set, the relay agent may handle the situation in four ways:
  • It may append its own set of relay options to the packet, leaving the supplied option field intact.
  • It may replace the existing agent option field.
  • It may forward the packet unchanged.
  • It may discard it.

Options available in DHCPv6 mode only:

-I
Force the use of the DHCPv6 Interface-ID option. This option is automatically sent when there are two or more downstream interfaces in use, to disambiguate between them. The -i option causes dhcrelay to send the option even if there is only one downstream interface.
-l [address%]ifname[#index]
("el") Specifies the "lower" network interface for DHCPv6 relay mode: the interface on which queries will be received from clients or from other relay agents. At least one -l option must be included in the command line when running in DHCPv6 mode. The interface name ifname is a mandatory parameter. The link address can be specified by address%; if it isn't, dhcrelay will use the first non-link-local address configured on the interface. The optional #index parameter specifies the interface index.
-u [address%]ifname
Specifies the "upper" network interface for DHCPv6 relay mode: the interface to which queries from clients and other relay agents should be forwarded. At least one -u option must be included in the command line when running in DHCPv6 mode. The interface name ifname is a mandatory parameter. The destination unicast or multicast address can be specified by address%; if not specified, the relay agent will forward to the DHCPv6 All DHCP Relay Agents and Servers multicast address.

It's possible to specify the same interface with different addresses more than once, and even, when the system supports it, to use the same interface as both upper and lower interfaces.

Description:

The Internet Systems Consortium DHCP Relay Agent, dhcrelay, provides a means for relaying DHCP and BOOTP requests from a subnet to which no DHCP server is directly connected to one or more DHCP servers on other subnets. It supports both DHCPv4/BOOTP and DHCPv6 protocols.

The DHCP Relay Agent listens for DHCPv4 or DHCPv6 queries from clients or other relay agents on one or more interfaces, passing them along to "upstream" servers or relay agents as specified on the command line. When a reply is received from upstream, it's multicast or unicast back downstream to the source of the original request.

See also:

RFC3315, RFC2132, RFC2131

Files:

The dhcrelay agent depends on the following libraries:

Caveats:

Using the same interface on both upper and lower sides may cause loops, so when running this way, the maximum hop count should be set to a low value.

The loopback interface is not (yet) recognized as a valid interface.

Parent topic: D
Related reference
dhclient
dhcpd