devb-mvSata

Note: You must be root to start this driver.

Syntax:

devb-mvSata [cam option[,option]...]
            [mvSata option[,option]...]
            [blk option[,option]...] &

Runs on:

QNX Neutrino

Options:

Note: Use commas (,) to separate the options. You can put the cam, mvSata, and blk groups of options in any order.

cam options

The cam options control the common access methods:

lun=mask: Enable Logical Unit Number (LUN) scanning for the devices specified in mask. The mask is a hex bitmask specifying which IDs to scan for; the default is 0x00.
quiet: Be quiet: don't display any information on startup.
verbose: Be verbose: display full information about SCSI units (devices) on startup.

mvSata options

The mvSata options control the driver's interface to the mvSata controller. If you've installed multiple controllers, you can repeat these options for each controller. Remember, however, to specify the mvSata keyword before each controller's set of options.

Interface-specific options:

irq=req

The interrupt used by the controller.

vid=vid

The vendor ID of the controller.

did=did

The device ID of the controller.

pci=index

The PCI index of the controller in the machine, where index is a value between 0 and the number of adapters.

nobmstr

Don't use busmastering.

port=N,device

Specify options for device on port N.

priority=prio

Set the priority of the processing thread. The default is 21.

timeout=timeout

Set the I/O request timeout, in seconds. The default is 10.

cache_line=size

Set the PCI cache line size (16, 32, 64, or 128 bytes). The default is obtained from the PCI configuration.
Device-specific options:

geometry=heads:cyl:sect

Specify the drive geometry.

nobmstr

Don't use busmastering.

multiblk=blks

Set multiblock mode, specifying the number of blocks per interrupt.

nonremovable

Report the device as being nonremovable.

chs

Use Cylinder-Head-Sector mode. The default is LBA.

blk options

The blk options control io-blk.so. If specified, they must follow the blk keyword.

Description:

The devb-mvSata driver is for Marvell 88SX50XX SATA interfaces. It supports vendor ID 0x11ab with at least the following device IDs:

Device ID	Chipset
5080	88SX5080
5081	88SX5081
5040	88SX5040
5041	88SX5041
6081	88SX6081
6041	88SX6041

Due to a chipset limitation, CD-ROM and DVD-ROM drives aren't supported.

Files:

The devb-mvSata driver causes io-blk.so to adopt various block special devices under /dev. These devices are normally named hdn, where n is the physical unit number of the device.

This driver could also require the following shared objects:

Binary	Required
cam-disk.so	For hard-disk access.
libcam.so	Always

Exit status:

The devb-mvSata driver terminates only if an error occurs during startup, or if it has successfully forked itself upon startup because it hadn't been initially started in the background.

0: The devb-mvSata driver wasn't started in the background and therefore forked itself. The original process terminated with a zero exit status, the forked process continued.
> 0: An error occurred during startup.

Caveats:

Unless overridden with the blk automount= option (see io-blk.so), devices are mounted as:

Device	Mountpoint	Filesystem type
/dev/hd0t77	/hd	`qnx4`
/dev/hd0t6	/dos	`dos`
/dev/hd0t11	/dos	`dos`

While there's no limit to the size of a disk or partition, the limit on I/O (i.e., the lseek(), read() and write() functions) depends on the type of filesystem mounted and on whether you use the 32- or 64-bit versions of these functions. This I/O limit has no effect on the partition size for mounted filesystems. The maximum number of blocks is 2³².

Known supported functions include:

chmod(), chown(), close(), closedir(), creat(), devctl(), dup(), dup2(), fcntl(), fpathconf(), fstat(), lseek(), mkdir(), mkfifo(), mknod(), open(), opendir(), pathconf(), read(), readdir(), readlink(), rewinddir(), rmdir(), stat(), symlink(), unlink() (not supported for directories), utime(), write()

Note that certain calls (such as pipe(), as well as read() and write() on FIFOs) may require the pipe manager.