Driver for USB 2.0 wireless adapters based on the Ralink RT2501USB and RT2601USB chipsets
io-pkt-variant -d rum ... &
where variant is either v4-hc or v6-hc
(io-pkt-v4 doesn't support Wi-Fi).
The devnp-rum.so driver supports USB 2.0 wireless adapters
based on the Ralink RT2501USB and RT2601USB chipsets.
This is a ported NetBSD driver;
its interface names are in the form rumX,
where X is an integer.
The RT2501USB chipset is the second generation of 802.11a/b/g adapters
from Ralink. It consists of two integrated chips, an RT2571W MAC/BBP and
an RT2528 or RT5226 radio transceiver.
The RT2601USB chipset consists of two integrated chips, an RT2671 MAC/BBP
and an RT2527 or RT5225 radio transceiver. This chipset uses the MIMO
(multiple-input multiple-output) technology with multiple antennas to
extend the operating range of the adapter and to achieve higher throughput.
This driver can operate in the following modes:
- BSS mode
- Also known as infrastructure mode, this is used when associating with an access point,
through which all traffic passes. This mode is the default.
- IBSS mode
- Also known as IEEE ad-hoc mode or peer-to-peer mode.
This is the standardized method of operating without an access point.
Stations associate with a service set.
However, actual connections between stations are peer-to-peer.
- Host AP
- In this mode, the driver acts as an access point (base station) for other cards.
- Monitor mode
- In this mode, the driver is able to receive packets without
associating with an access point.
This disables the internal receive filter and enables the card to capture
packets from networks which it wouldn't normally have access to, or to scan
for access points.
The devnp-rum.so driver supports software WEP.
Wired Equivalent Privacy (WEP) is the de facto encryption standard for wireless networks.
It can be typically configured in one of three modes: no encryption; 40-bit encryption; or
Unfortunately, due to serious weaknesses in WEP protocol it is strongly recommended
that it not be used as the sole mechanism to secure wireless communication.
WEP is not enabled by default.
You can also use this driver in conjunction with
to provide WPA / WPA2 encryption.
You can use
to configure the devnp-rum.so driver at runtime:
- bssid bssid
- Set the desired BSSID.
- Unset the desired BSSID.
The interface automatically selects a BSSID in this mode, which is the default.
- chan n
- Set the channel (radio frequency) to be used by the driver based
on the given channel ID n.
- Unset the desired channel to be used by the driver.
The driver automatically selects a channel in this mode, which is the default.
- media media
- This driver supports the following media types:
- autoselect — enable autoselection of the media type and options.
- DS1 — 802.11b DS 1Mbps operation.
- DS2 — 802.11b DS 2Mbps operation.
- DS5 — 802.11b DS 5.5Mbps operation.
- DS11 — 802.11b DS 11Mbps operation.
- OFDM6 — 802.11a/g OFDM 6Mbps operation.
- OFDM9 — 802.11a/g OFDM 9Mbps operation.
- OFDM12 — 802.11a/g OFDM 12Mbps operation.
- OFDM18 — 802.11a/g OFDM 18Mbps operation.
- OFDM24 — 802.11a/g OFDM 24Mbps operation.
- OFDM36 — 802.11a/g OFDM 36Mbps operation.
- OFDM48 — 802.11a/g OFDM 48Mbps operation.
- OFDM54 — 802.11a/g OFDM 54Mbps operation.
- mediaopt opts
- This driver supports the following media options:
- hostap — select Host AP operation.
- ibss — select IBSS operation.
- monitor — select monitor mode.
- -mediaopt opts
- Disable the specified media options on the driver and return it
to the default mode of operation (BSS).
- mode mode
- This driver supports the following modes:
- 11a — force 802.11a operation.
- 11b — force 802.11b operation.
- 11g — force 802.11g operation.
- nwid id
- Set the network ID.
The id can either be any text string up to
32 characters in length, or a series of hexadecimal digits up to
An empty ID string (the default) allows the interface to connect to
any available access points.
Note that network ID is synonymous with Extended Service Set ID (ESSID).
- nwkey key
- Enable WEP encryption using the specified key.
The key can either be a string, a series of hexadecimal digits (preceded by
0x), or a set of keys of the form n:k1,k2,k3,k4, where
n specifies which of the keys to use for transmitted packets,
and the four keys, k1 through k4, are configured as WEP keys.
If a set of keys is specified, a comma (,) within the
key must be escaped with a backslash.
|| If you use multiple keys, their order must be the same within the network.
The devnp-rum.so driver can use both
40-bit (5 characters or 10 hexadecimal
digits) or 104-bit (13 characters or 26 hexadecimal digits) keys.
- Disable WEP encryption. This is the default mode of operation.
||Native io-pkt and ported NetBSD drivers don't put entries
into the /dev/io-net namespace, so a
command for such an entry won't work properly in buildfiles or scripts.
instead; for example, instead of waitfor /dev/io-net/rum0, use
if_up -p rum0.|